⎝⎛叫我棋牌⎞⎠

Welcome to Dongguan Meijun Sandblasting Equipment Store!
Meijun Sandblasting Equipment
Meijun Sandblasting Equipment
Focused on sand blasting machine and sand blasting machine accessories for more than ten years
Pay attention to materials, high quality raw materials, long life
contact details
Meijun Sandblasting Equipment
Product Categories
4News Center
Your location: ⎝⎛叫我棋牌⎞⎠- > News

Sandblasting machine parts introduction The surface layer undergoing cyclic plastic deformation will vary with different materials


Sandblasting machine parts introduction The surface layer undergoing cyclic plastic deformation will vary with different materials

Shot peening is a process in which the projectile flow continuously hits the surface material of the fastener, thereby causing the surface layer (depth of about 0.05 to 0.20 mm) to undergo cyclic plastic deformation. The surface layer subjected to cyclic plastic deformation will vary with the material according to one or more of the following:

1. A residual compressive stress field is formed in the surface layer;

2. Changes in the substructure (subgrain) size and lattice distortion of surface materials;

3. Plasticity-induced phase change;

4. Changes in material density in the plastic layer.

The sand blasting machine accessories describe the residual compressive stress field introduced by the blast plastic deformation of the surface layer of the material. After superimposing the tensile stress with the applied alternating stress on the same cross section, the maximum tensile stress that the material undergoes is moved from the surface to the sub-surface position.

Fatigue cracks on the surface without shot peening specimens originated on the outer surface, while fatigue cracks strengthened by shot peening surface deformation originated on the subsurface layer. Theoretical analysis confirms that after the deformation residual stress induces fatigue cracks on the secondary surface of the material, an internal fatigue limit of 1.05 to 1.35 times higher than the surface fatigue limit can be obtained.

Surface shot peening is an effective surface strengthening process to improve the fatigue corrosion-resistant stress corrosion and hydrogen embrittlement fracture of fasteners. Projectiles include cast steel shots, glass shots, ceramic shots, etc. The surface roughness of the reinforced fastener is 0.65 μm to 2 μm, and the achievable surface roughness is 0.63 to 2.5 μm. The reliability and durability of the workpiece can be significantly Improve and improve.

Shot peened glass beads (GlassBead) is a kind of abrasive with unique characteristics widely used in cleaning or metal surface strengthening treatment, mainly used in sandblasting equipment. Shot peened glass beads are crushed and sorted from high quality cullet. In manufacturing, the broken glass is fused into a ball and then annealed to eliminate internal stress and prevent breakage. This transparent and clear spherical structure product will not have particles embedded in the workpiece during use, pollute the workpiece or cause other damage. With different sizes of abrasives and different operating parameters, shot glass beads will achieve different gloss levels on the surface of the workpiece. The use of shot peened glass beads for selective local coverage and controlled blasting on the surface of the workpiece can produce special decorative effects.

The excellent performance of the shot blasted glass beads of the sand blasting machine parts will not damage the surface of the workpiece when cleaning or deburring the workpiece with strict deviation requirements, which is very suitable for selection. Moreover, the inherent strength of shot peened glass beads makes it suitable for use in equipment capable of recycling abrasives.






Related Searches: Sandblasting Machine Parts , Pressure Sandblasting Machine , Sandblasting Helmet , Chongqing Please visit: http://sereio.com



⎝⎛叫我棋牌⎞⎠ - About Us - Products - Success Stories - Cooperating Clients - Equipment Video - Company Environment - News Center - Industry News - Message - Recruitment - Contact Us
LOGO
Dongguan Humen Meijun Sandblasting Equipment Store Copyright © Copyright 2017 Technical Support: Dongguan Website Construction [ GMAP ]
Address: Building 1-1, Building A, Qihe Industrial Park, No. 33 Xinxing Road, Xinlian Community, Humen Town, Dongguan City. Tel: 0769-82261696 / Mr. Zhong
* The relevant webpage materials and related resources on this site are from the Internet. If there is any infringement, please inform us quickly. We will delete it within 24 hours. [ Background Management ]
Main: sand blasting machine, water blasting machine, derusting blasting machine, boron carbide nozzle, blasting machine accessories, blasting gun, mobile phone shell blasting machine, aluminum plate blasting machine, Dongguan blasting machine accessories, environmental protection Sand room, Dongguan sand blasting machine, environmental protection sand blasting room [ Baidu Statistics ]
【粤 ICP 备 09153882 号 -1】 【粤 ICP 备 09153882 号 -2】
手机电玩平台 欢乐拼三张 天天电玩城 七乐彩