⎝⎛叫我棋牌⎞⎠

Welcome to Dongguan Meijun Sandblasting Equipment Store!
Meijun Sandblasting Equipment
Meijun Sandblasting Equipment
Focused on sand blasting machine and sand blasting machine accessories for more than ten years
Pay attention to materials, high quality raw materials, long life
contact details
Meijun Sandblasting Equipment
Product Categories
4Products
毛边处理喷砂机-环带式

Unedged sand blasting machine-endless belt type

Details

Deburring Sandblasting Machine, Deburring Machine, Annular Belt Deburring Sandblasting Machine, Deburring Sandblasting Machine

Hot-hard plastic burr processing sandblasting machine PLASTIC DEFLASHER

parameter:

impeller

Impeller

Projection

Capacityof projection (kg / min)

15

Projection speed

Speed of projection (m / sec)

40

50

60

Number of revolutions

Revolution (rpm)

0 ~ 2900

0 ~ 3

Belt(Drum)speed(m/min) Belt (Drum) speed (m / min)

6

Projection material circulation device

Recycle device of projection

Impeller self-sufficient

Self sustaln Impeller

With shaker

C / W Vibrating sleve

Additional humidification and blowing device

With automatic atomizer and blower

Product handling capacity

Yield

capacity

ε ) Capacity ( ε )

30

25

weight

Weight (kg)

15

10

length

Max.length (mm)

550

Dust collector Dust collector

Concealed type Concealed type


FEATURES :


This is optimal automation machine specially designed for handling the burr of   the compression and injection formation of thermal hard plastic, bake lite and   resin products.

1.The dust collector isconcealed inside the body. Optimal arrangement of operation panel for easy operation, simplemaintenance

2.The abrasive projected by high speed revolving impeller which capable cleaning of the burr on the surface, hole, recssion of the product instantly, and exerting the high cleaning efficiency.

3.The treated proucts are lustrous and shinning ,, for this machine is equipped with automatic atomizer device andblowing evice which remove dust and dirt.

4.This machine allow long time continue operation without part and component replaccment, so the maintenance cost is minimal and capable of   mass quantity handling, one machine is equal   to 10 ~ 15 worker, is the best mean to reduce your cost and labor.

 

feature

专门为压缩及射出成型等热硬性塑料,电木,树脂类产品的毛边清理而设计的自动化之最佳机械。 Hot-hard plastic burr processing sand blasting machine is the best automatic machine designed for the burr cleaning of hot-hard plastics, bakelites and resin products such as compression and injection molding.

集尘机藏于机体内。 1. The dust collector is hidden inside the machine.

At the entrance, the operation panel is well arranged, the operation is easy, and the maintenance is simple.

2. 而发挥其高效率之清扫能力。 The projection material is ejected by a high-speed rotary impeller, with a large radiation area and dense projectiles. The burrs on the surface of the product, internal holes, recesses, and difficult-to-treat areas can be removed in a short time , and its high-efficiency cleaning ability is exerted.

处理后,个个漂亮并有光泽。 3. After the products are processed by this machine , they are all beautiful and shiny. (Because the machine is equipped with an automatic humidification and automatic blowing device for special dust removal)

本机械可长期连续使用,而不需更换部品,所以保养费很少,而且可以大量处理,每台机械可抵10~15人之产能,是降低成本减少人工的好帮手。 4. This machine can be used continuously for a long time without replacement parts, so the maintenance cost is very small, and it can be handled in large quantities. Each machine can reach a capacity of 10 ~ 15 people, which is a good helper to reduce costs and labor.

毛边处理喷砂机,毛边机,环带式毛边喷砂机,毛刺处理喷砂机

 

This machine is used to process the burr on the surface of the thermosetting plastic products that are compressed or injection molded.

Abrasive spraying is a self-contained projection device. It integrates a chassis, an endless belt conveying device, and a dust collecting device. It is a spray washing machine with a simple appearance, which does not take up space and has high efficiency.

The projection material (plastic granules) is projected on the product through the high-speed rotating impeller, and the burrs in the shape of a sheet and the burrs in the recesses or holes can be removed in a short time. The amount of projected power can be adjusted on the inverter keyboard on the control panel to the appropriate number of revolutions.

The spraying and washing room is composed of an endless belt conveyor, and all rubbers are laid in the room. When the input product is stirred in the forward rotation of the endless belt, the projected material thrown out at a high speed impacts to achieve the effect of uniform deburring.

The projected material that is projected can be continuously used through a delicate circulation system. The powdery burr and the smaller projection material are attracted and collected by the dust collector, while the larger burr is filtered by the screen.

There is a nozzle for humidification in the middle of the suction pipe. An appropriate amount of moisture can further enhance the spray washing effect, prevent dust from adhering, and increase the life of the projection material.


Notes on operation
1. Product processing time varies depending on the processing volume, shape, and projection material. The adjustment method is that the rotation speed of the impeller is between 45 ~ 60HZ (2250 ~ 3600R.PM), which is adjusted to a good projection time, generally about eight minutes.
2. The abrasion-resistant rubber of each part is flammable (lighting point is about 300 ° C), please keep out of fireworks.
3. Before starting work, please confirm whether each door is completely closed. Especially, do not open the operation door during spray cleaning operation.
4. During operation, the projection material will be gradually consumed, and the impeller projection amount will gradually decrease. It should always be checked by the front door inspection window, or compared with the current value of the projection ammeter. If it is reduced, please add an appropriate amount.
5. If abnormal sounds or overheating of bearings and motors occur during operation, immediately stop the machine for inspection and turn off the power to ensure safety during maintenance.
6. Before the operation starts or after the operation is completed, the condition of each part should be checked. If there is abrasion, please repair and replace it immediately.
7. The amount of water in the humidifying bucket should be checked daily, and please replenish it when it is insufficient.
8. After daily operation, please stop the machine and shake the handle on the left side of the chassis for a few times to shake off the dust in the dust pipe.
9. After daily operation, please clean up waste and dust.
10. If the rubber band is shifted or slipped, adjust the adjustment screws on both sides of the case slightly.
11. Before spraying and washing the product, please screen and remove the sundries and other sundries, and then put it into the spraying to prevent the belt from being scratched, so as to extend the life of the belt.
12. The endless belt conveyor has a safety tip device. If the endless belt is jammed, the end of the safety edge will be automatically cut off and the endless rotation of the endless belt will be stopped immediately without damage to the machine. Please remove the jammed items, remove the chain cover, and replace New safety tips.
13. For chains and bearings, please add grease twice a month.
14. After the door sponge is worn, please replace it with a new one.
15. If the nozzle for static elimination is blocked, please clean it with a bristle brush, bamboo stick and plastic needle. Never use a metal through needle.
16. After use, please turn off the main switch.
After the operation preparation machinery is set up, please prepare one by one according to the following items:
1. Connect the main power. (Please follow the wiring shown in the P11 power wiring diagram)
2. Connect the compressed air source. (Nozzle blowing pressure is within 0.5kg / cm2)
3. Have a bucket ready and add clean water or antistatic fluid.
4. Take out the cover from the lower door on the front and put it into the projection material. (Standard input is 10kg)
5. Timer T4 for setting the humidification time (depending on the nozzle aperture size, there are three types: ∮1.1mm, ∮0.71mm, ∮0.51mm:
Large aperture ∮1.1mm, open for 1 second and close for 15 seconds.
Medium bore ∮0.71mm, open for 1 second and close for 12 seconds,
Small aperture ∮0.51mm, open for 1 second and close for 10 seconds)
6. Set timer T3 for projection time (setting reference is 8 minutes).
7. Set timer T5 for end alarm waiting time (setting reference is 2 minutes).
8. Set the timer TR for the end alarm time (setting reference is 1 second).
9. Start each drive unit and confirm the rotation direction of the motor (just confirm that the belt is rotating normally).
Confirmation method: Press the belt forward switch, and the belt should turn to the inside of the machine. Otherwise, please R. in the main power supply. S. T. The positions of any two lines in the three lines can be reversed.
After the above tasks are completed, please start according to the precautions and operation sequence on the next page.
Remarks: 1. Mechanical settings must consider operating space and maintenance space.
2. If spraying and washing special products, such as: bakelite with fiber, urea, engineering plastic and other products. Because static electricity is easy to occur, please use antistatic liquid, which can eliminate static electricity and make the product surface cleaner

⎝⎛叫我棋牌⎞⎠ - About Us - Products - Success Stories - Cooperating Clients - Equipment Video - Company Environment - News Center - Industry News - Message - Recruitment - Contact Us
LOGO
Dongguan Humen Meijun Sandblasting Equipment Store Copyright © Copyright 2017 Technical Support: Dongguan Website Construction [ GMAP ]
Address: Building 1-1, Building A, Qihe Industrial Park, No. 33 Xinxing Road, Xinlian Community, Humen Town, Dongguan City. Tel: 0769-82261696 / Mr. Zhong Visits:
* The relevant webpage materials and related resources on this site are from the Internet. If there is any infringement, please inform us quickly. We will delete it within 24 hours. [ Background Management ]
Main: sand blasting machine, water blasting machine, derusting blasting machine, boron carbide nozzle, blasting machine accessories, blasting gun, mobile phone shell blasting machine, aluminum plate blasting machine, Dongguan blasting machine accessories, environmental protection Sand room, Dongguan sand blasting machine, environmental protection sand blasting room [ Baidu Statistics ]
【粤 ICP 备 09153882 号 -1】 【粤 ICP 备 09153882 号 -2】
手机电玩平台 欢乐拼三张 天天电玩城 七乐彩