⎝⎛叫我棋牌⎞⎠

Welcome to Dongguan Meijun Sandblasting Equipment Store!
Meijun Sandblasting Equipment
Meijun Sandblasting Equipment
Focused on sand blasting machine and sand blasting machine accessories for more than ten years
Pay attention to materials, high quality raw materials, long life
contact details
Meijun Sandblasting Equipment
Product Categories
4Products
双缸双枪压力式喷砂罐喷砂设备

Double-cylinder double-gun pressure type blasting tank blasting equipment

Details

Rust blasting machine-pressure blasting machine-manual blasting machine-open blasting machine-dry blasting machine-high pressure blasting machine-anti-corrosion cleaning equipment-pretreatment equipment

Pressure mobile sand blasting machine is a kind of pre-processing machine for engraving and thermal spraying. It uses compressed air as the power to spray clean and dry abrasive at high speed to the surface of the workpiece to be sprayed to achieve surface cleaning, woolening, engraving marks, etc. If required, it can also be used for paint removal, welding seam rust removal, and hair blasting (atomization) treatment for preparing frosted glass and other workpieces. The effect is very significant. The cleaning level reaches SA2.5-3.0, and its roughness reaches the process requirements. The product has a wide range of uses, compact structure, simple maintenance, easy to use, etc. It is a necessary machine for thermal spraying (welding) various anticorrosive layers.

The control system of the pressure-holding pressure mobile sand blasting machine is composed of an intake shut-off valve (basic type is a ball valve) and a sand control valve assembly.

The characteristic of this model is that each time the valve is opened, the air shut-off valve (4 intake valve), the sand control valve (8) must be activated, the gas of the blasting cylinder will increase and discharge, and each time the switch is There is a certain period of time, because all the gas from the blasting cylinder has to be exhausted, the operator can lower the spray gun.

Because the manual abrasive valve is used, the sand regulating valve is always open when shutting down. Therefore, each time the switch is opened, there will be a certain amount of sand stored in the sand tube. There will be an instant pulse when the gun is fired. After the emptying is completed, the sand blasting gun can normally blast, requiring a delay of 5-10 seconds.

If you need to shut down and stop working, first close the air inlet valve, and then close the sand regulating valve (8) (or sand dropping ball valve) at the bottom of the sand tank. After the remaining sand and air in the sand pipe are exhausted, close the side air valve-ball valve (4A) to lower the spray gun to ensure safety.

I. System parameters, precautions and requirements of this model:

1 Equipment main technical parameters:

Cylinder diameter: 900mm-2100MM Sand blasting efficiency: 15-35 square / H (depending on the size of the pipeline used and the pressure of the gas source)

Cylinder height: 1700-2200mm, sand blasting grade: SA2.5-3.0

Volume: 0.8-1.0 cubic meters Air consumption: ≥3 cubic meters / min (8MM spray gun)

Air supply pressure: 0.6-0.7Mpa (8KG) must not exceed 8KG pressure

35HP (8MM nozzle) / 50HP (10MM nozzle) / 75HP (12MM nozzle)

Design pressure: 8.8KG

Experimental pressure: 1.15MPA (11.5KG)

Features: Low failure rate, less wearing parts, less investment, high efficiency, fixed structure, fixed-point sandblasting room.

Sand jar sealed mushroom head size: replacement time: can not be sealed or air leakage must be replaced

Sand jar seal O-ring size: Replacement time: can not be sealed or air leakage must be replaced

Sand mouth diameter under the tank: 2 inch internal thread

Sand control valve: 2 inch threaded external tooth interface Valve core replacement time: 600-800 hours

Side main pipe: 1-1 / 4 inch water pipe (one inch two) Ball valve: 1-1 / 4 inch internal tooth straight ball valve

Sand pipe joint: 1-1 / 4 inch dragon catch Sand gun joint: 1-1 / 4 inch inner tooth fine tooth

Sandblasting gun: 1-1 / 4 inch fine teeth single inlet throat diameter 10MM Spray gun material: outer steel sleeve high temperature sintered boron carbide nozzle

Supply pipe requirements: inner diameter ≥32MM

Sandblasting pipe requirements: 25MM or 32MM inner diameter high wear-resistant and pressure-resistant sandblasting pipe with a pressure resistance of 10mpa.

2 local advantages:

1. Compact structure, superior performance, simple and convenient operation;

2. The design and production of the cylinder body comply with the pressure vessel standards, which is safe and reliable.

3. Standard universal parts are used for easy replacement and lower cost, especially the wear parts are separated from the fixed parts, and wear parts are installed in the middle, which effectively reduces the replacement loss cost;

4. It can be retrofitted and installed with instantaneous control function at any time.It adopts electric control or pneumatic control to meet the different needs of customers and can be operated by one person.

5. The shell is thickened and painted with anti-rust paint, which is beautiful and practical. .

双枪喷砂机,双缸喷砂机,高压喷砂机,1000P喷砂机】

3 Abrasive particle requirements:

Sand used for sandblasting and rust removal requires particles with hard, angular, dry and free of dirt and other impurities; the standard is brown corundum sand, economical is better quartz sand, coarse river sand can also be used; meanwhile, sand Material transportation conditions, unit price, recycling capacity and other factors; the particle size of the sand is preferably 0.5 ~ 1.5mm, it must be dried before screening, stored in the shed, indoor, and the size of the sieve is: coarse sieve 40 ~ 48 holes (grain 1.2mm diameter), fine sieve 372 ~ 476 holes (particle diameter 0.3mm)

When adding sand to the sand tank, a sieve with a size of 16 # or more should be covered on the top of the tank to screen the sand particles to prevent foreign objects from falling into the tank and causing blockage of the sand valve or nozzle.

4 Air source requirements:

Air source pressure: 0.6-0.7Mpa (8KG) must not exceed 8KG pressure

Power comparison: 35HP (using 8MM nozzle) / 50HP (using 10MM nozzle) / 75HP (using 12MM nozzle)

The compressed air must be processed by a cooling device and an oil-water separator to ensure that it is dry and free of oil;

The oil-water separator must be cleaned regularly;

Generally, the air pressure of the air compressor is 6.0 × 105 ~ 6.5 × 105Pa, and the pressure change range is 0.5 × 105 ~ 1.0 × 105Pa.

Generally, the pressure of the sand bucket is 4.5 × 105 ~ 5.5 × 105Pa, and it must not be less than 4.0 × 105Pa.

If the pressure of the sand tank exceeds 0.7MPA, stop the gas supply and drain the gas from the tank, check the cause and deal with it.

Second, use
1. Preparation

Pre - use protection requirements for rust removal and sand blasting machine :

Inspection-Non-sandblasted areas should be protected before blasting.

Check-whether the various pipes and control valves of the blasting machine are connected before the blasting, and whether they are in the appropriate switch position-the sand control valve (8) and the intake valve (4) must be closed, and the exhaust valve (17 ) Is off.

Check-whether the protective tools, safety belts (ropes) and oxygen supply equipment worn by the blaster are safe and reliable, and the nozzle wear (when the orifice

The nozzle should be replaced when the diameter increases by 25%).

Connect each connection and all pipelines as shown in the figure, and check whether it is firm and sealed.

Check whether the pneumatic control system is normal and whether the manual control switch is normal.

Check-the exhaust valve is closed.

1) Connect the sand blasting machine to the air source with an air hose, and tighten it correctly (use a special joint to connect and fix, and add iron wire to pull the air pipe) to prevent the pipe from coming off.
2) Connect the sand blasting pipe to the quick connector of the abrasive valve outlet and lock it (lock the card hole with a screw after the dragon catches the butt) to prevent the sand pipe from falling off during use and creating an accidental danger.
3) Put the clean and dry abrasive into the barrel of the sand blasting machine. (It is easy to add sand within 2/3 of the sand tank)
4) Start the air compressor so that the indicated pressure reaches the required working pressure. The air compressor is placed on the air outlet of the sand blasting machine to prevent dust caused by sand blasting from being sucked into the air compressor.

5) Wear protective equipment for sandblasting.

2. Operation control of steel structure derusting and sandblasting machine :

1) First close the side air pipe ball valve switch (4A), and close the tank bottom sand regulating valve or ball valve (8) at the same time. The sandblaster holds the sandblasting gun to prepare for work.
2) Turn on the air source of the air compressor, turn on the balloon valve switch (4), the air source of the intake valve is turned on, and the cylinder starts to intake air;

Please observe the pressure gauge, the normal pressure value is in the range of 4-6MPA. If the pressure of the pressure gauge is too large and exceeds 7MPA, stop the gas supply and drain the gas in the tank. Check the cause of the excessive pressure value and contact the supplier (air compressor or (Blasting machine) consulting related matters;

3) After venting, the high-pressure air enters the sand cylinder, and the cylinder is pressurized. The umbrella-shaped sealing valve on the top automatically lifts up and seals the inlet. The pressure in the sand blasting machine continues to rise, and the sand blasting gun can automatically enter the sand blasting preparation At this time, the sand blaster should hold the spray gun firmly and be ready to blast at any time.


4) Open the side air pipe ball valve switch (4A), the air from the spray gun comes out, and then open the sand valve ball valve (8) under the sand cylinder, sand blasting starts.

During the blasting operation, according to the blasting state, adjust the handle on the abrasive valve (the sand valve ball valve 8 under the sand cylinder) to adjust the abrasive outlet flow rate (closed in the horizontal direction and fully opened in the vertical direction). It should not be too large. When viewed under the sun or other bright light sources, the air flow containing abrasives is not much different from the pure air flow.

5) At the end of the operation, the blaster still needs to hold the spray gun tightly, and the other assists the blaster to shut down the machine.

Close the air inlet valve switch (4) --- close the sand valve under the sand tank ball valve (8) ---- close the side air pipe ball valve switch (4A)

At this time, the blasting gun automatically stops the blasting operation slowly. The blaster needs to wait for the remaining sand and air in the sand pipe to exhaust, before lowering the blasting gun to ensure safety.

After all the procedures are completed, there is still high-pressure gas in the sand cylinder, and a short pause can continue with steps 1) -4) for sandblasting. If the machine needs to be stopped, manually open the exhaust ball valve (17) on the top side of the sand tank to exhaust the gas in the tank.

Blasting distance: The distance between the spray gun and the surface of the base steel is preferably 100 ~ 300mm during sandblasting.

Blasting angle: The angle between the spraying direction and the normal surface of the base steel is preferably 15 ° ~ 45 °.

After the sandblasting and rust removal, before the next process, if it rains or other conditions cause the surface of the base steel to be wet, after the environment has reached the construction conditions, dry the surface with dry compressed air before carrying out the sandblasting construction. . If re-blasting is required, the abrasive requirements must not be reduced, otherwise the roughness will be reduced and the subsequent spraying adhesion will be low.

After the blasting operation is completed, the main air source of the compressor is closed, the air supply to the compressor is stopped, the exhaust valve of the compressor is opened, and the residual gas in the compressor is discharged. The power is turned off and the air compressor is turned off. If the blasting machine is not used for a long time, the remaining abrasive in the cylinder needs to be cleaned to prevent wet agglomeration or block sand.

Third, stop
When the blasting machine takes a long time to shut down, the abrasive in the barrel should be cleaned to prevent failure due to the damp of the abrasive when it is reused. The steps to clean the abrasive are:
1. Remove the nozzle.
2. Place the sandblasting hose in a container.
3. Close the side air valve (4a) and exhaust valve (17) and open the abrasive valve to a large extent.
4.Open the air inlet valve (4) and let the sandblasting machine operate until the cylinder is more than the abrasive, and then open the side air valve (4a) to blow the abrasive in the sand tube clean.

The sand blasting machine should be covered when it is placed outdoors at night to prevent water from entering the bucket.


Fourth, maintenance
1.Replace closed valve (umbrella bucket)
Open the service port valve, and use a small pipe wrench to unscrew the connection (conduit) under the conical closed valve (umbrella bucket) and remove them from the barrel. Replace it with a new shut-off valve. Install the inspection hole cover and tighten all the screws.
2.Replace the inlet seal
Use your nails or a screwdriver to gently remove the old seal and press the new seal into the seal seat.
3. Regularly check the lubrication and wear of the O-rings, pistons, springs, seals and other parts in the intake valve (air shut-off valve) and exhaust valve.

Five, troubleshooting
1.Clog
1) No abrasive or air at the nozzle outlet. Close the inlet valve (4) and open the exhaust valve (17). After the pressure of the sandblasting machine is unloaded, check whether the nozzle is clogged. If the clogging needs to be cleaned, continue to blast ;

2) If there is air and no abrasive, if the nozzle is not blocked, it may be blocked at the sand control valve or at the sand mouth under the tank. The sand valve needs to be removed for inspection, foreign matter is discharged, and the sand valve is continued after the sand valve is reinstalled.

Open the abrasive valve to a very large limit, quickly open it and then immediately close the main air inlet valve (4), then quickly open the main air inlet valve (4), multiple cycles, impact the blockage with pulse force, if this method does not work, It needs to be disassembled and checked.
⎝⎛叫我棋牌⎞⎠ - About Us - Products - Success Stories - Cooperating Clients - Equipment Video - Company Environment - News Center - Industry News - Message - Recruitment - Contact Us
LOGO
Dongguan Humen Meijun Sandblasting Equipment Store Copyright © Copyright 2017 Technical Support: Dongguan Website Construction [ GMAP ]
Address: Building 1-1, Building A, Qihe Industrial Park, No. 33 Xinxing Road, Xinlian Community, Humen Town, Dongguan City. Tel: 0769-82261696 / Mr. Zhong
* The relevant webpage materials and related resources on this site are from the Internet. If there is any infringement, please inform us quickly. We will delete it within 24 hours. [ Background Management ]
Main: sand blasting machine, water blasting machine, derusting blasting machine, boron carbide nozzle, blasting machine accessories, blasting gun, mobile phone shell blasting machine, aluminum plate blasting machine, Dongguan blasting machine accessories, environmental protection Sand room, Dongguan sand blasting machine, environmental protection sand blasting room [ Baidu Statistics ]
【粤 ICP 备 09153882 号 -1】 【粤 ICP 备 09153882 号 -2】
手机电玩平台 欢乐拼三张 天天电玩城 七乐彩